Work from a clean system. If you have attempted to install the Hauppauge software before and had troubles, then use the Hauppauge HCW Clear software to remove all the Hauppauge software and drivers from your system. Reboot your system before continuing if you used the HCW Clear program. Step 2. Download Hauppauge Software. In this step we will download and unzip all the required software and drivers needed for the installtion.
DO NOT install any of them yet. Just get everything ready. You can find the older drivers versions here. Download the file and unzip it to a temporary location.
If you want to use the built in IR blaster, you must download and unzip three additional files. Here is a picture of the three IR related programs that you need to download and unzip. Uninstall SageTV. As long as you don't manually delete the SageTV folder under the Program Files, you will not loose any settings, tunes, histories, etc.
Simply uninstalling Sage does not delete that folder. Step 4. After uninstalling SageTV, I would recommend rebooting your computer to make sure everything Sage related is cleared from the system. Optional Install drivers for any other Hauppauge tuners you wish to use. Step 5. If the "New Device Found" program pops up after the reboot, close it out. You need to use the setup program that comes with the Hauppauge drivers.
Once the drivers are installed, if you want to use the built in blaster, then follow these additional steps. Otherwise skip to step 6. To use the built in blaster, we must install the three IR related programs that we downloaded and unzipped in step 2.
Once all three of these programs are installed, continue to step 6. Step 6. Step 7. Open the BlasterCfg program. Verify that the blaster is found by looking that the bottom right corner of the program. You should find something like what is shown below.
To test the blaster is working, press the "Send" command to change the channel of the STB. If it doesn't change the channel, then continue searching for a STB listed that does change the channel. There is nothing to save. Also, verify that the IR program started automatically when you rebooted in Step 6 by looking for the IR icon in the system menu. There should be a black and red icon in the lower right system menu of the start menu.
It looks similar to an iPhone. Reinstall SageTV. Reinstall SageTV using the normal installation method. There is no conversion of the audio format. Currently, the Arcsoft TME application will only support editing from the beginning or the end of a clip to preserve AC-3 5. Any editing or cuts made in the middle segments of a clip will result in the audio being transcoded back to 2 channel audio. AC-3 5. If you are creating a standard DVD the audio will be transcoded to 2 channel.
Creating MP4 files will also result in 2 channel audio. The component video outputs act as a pass through for live video streaming from your video source through the HD PVR back to your TV monitor. Most of the time this is caused by the display adapter, make sure your video card meets the minimum requirements. Also try updating to the latest drivers supplied by the manufacturer. Check to see how you have your Television connected to your set top box.
In order for the audio pass through to operate correctly you need to configure the settings in the Total Media Extreme application. No, currently none of the VBI is captured in the stream. This feature will be added some time in the future. This information has been spread on user forums, however, Revision C3, D2, and E1 revisions are all functionally equivalent, and will address the same issues. The audio format is "passed through" to the recording. In other words, if your source includes AC-3 audio, this audio will be used in your recording.
The default formats you can record in are:. Note: there are two versions of StreamEez. There is also a stand alone version of StreamEez which is described below. StreamEez version If you are running in any other video mode, you will see either a black screen or distorted video. Check your video mode! Note: your Gaming PC screen may go black for several seconds and then you will be back at the Windows desktop. Under Resolution , set to either X or X Under Multiple displays , set to Duplicate these displays.
You should see your PC screen on the video monitor. If you do not, click the Windows button on your keyboard and at the same time the P key. Then select Duplicate. If you have set your PC's video mode correctly step 2 above , you should see your PC screen on the video monitor. Right click and select Set as default device.
If you are listening to sound from your Gaming PC through speakers and not on your video monitor, to hear audio without any audio delay you will need to split the audio coming from your Gaming PC. These adapters are common and can be purchased from Radio Shack or online. Click here for instructions from YouTube.
Hauppauge Capture Quick User Guide. Hauppauge Capture Manual. The Rocket has a built-in audio mixer which will take microphone audio and mix it with game audio so you can add game commentary to your game play recordings. In this mode, recordings are made to the hard disk inside your PC and the USB thumb drive is not used.
The Rocket can be used either with or without a PC. When used standalone it records to a USB thumb drive which is plugged into the front of the Rocket and power is provided from the USB port on the back of the Rocket 5v at 1.
When connected to a PC, you can use Hauppauge Capture to record, upload and stream. Recordings are made to your PCs hard disk drive. When PC connected, settings such as the video and audio source is 'sticky' and will be used when standalone. Video input resolutions can range from standard definition x up to p If you have a self powered hard drive 'self powered' means it has its own power supply which is USB connected, you can plug the USB cable from the hard drive into the front of the Rocket in place of the USB thumb drive.
The Rocket itself does not have enough power to drive a hard drive, so it must be self powered. You should see your recording also being played back to your TV set.
As soon as you plug in the thumb drive, the Samsung TV set will recognize the thumb drive and allow you to play recordings back to your TV screen. If you have any questions on these connections, please email us at techsupport hauppauge. Then open Hauppauge Capture and adjust the bit rate Quality up or down using the bitrate slider. Then close Hauppauge Capture. Any adjustments you make in Hauppauge Capture except for the microphone audio volume, which is adjusted standalone from the control panel on top of the Rocket will be saved when you exit the application and be applied to standalone mode.
In about 15 seconds you should now see your composite video source in the OBS Preview window. HD PVR 2 can adjust the color settings of both the recordings and the passthrough video.
Check the USB cable! If the Yellow light blinks once and then turns to Blue, it means that Hauppauge Capture cannot detect a video signal. There are several reasons this can happen: You did not plug in a video cable, or you have the wrong video source selected in Hauppauge Capture.
And check your video cable and your cable connections! If you have a bad cable or have made a mistake plugging in the cables, you will see a Blue light. If you are recording from an Xbox , make sure your video mode is set to either p or p.
Here is where you can find instructions on setting your video mode. If you are recording from a PC game system, make sure you have set your PC graphics video mode to p at 60Hz.
Here is where you can find instructions on setting your PC video mode. There are a number of reasons this could happen. If you continue to see the Red light while recording, check your cabling and if you continue to have problems, contact Hauppauge technical support. Black screen in the Capture preview window and no video on your TV set: First, make sure, in the Capture tab: if you are using an Xbox, make sure your Xbox is set to p or p.
Some other Xbox video formats will give a black screen in Capture and your TV set. To do this on the PS3 Slim, push the power button on the front until the light goes red. Then push and HOLD the button until you hear two beeps.
Then you can release the power button and the PS3 video format will be set to the default. Black screen in the Hauppauge Capture preview window: First, make sure, in the Capture tab: Source: make sure your Hauppauge device is selected.
Check you cables! If you choose the wrong video source, you will get a black screen. For example, if you connect Component video but Arcsoft Capture is set for S-Video, you will get a black screen. Uncheck "hardware acceleration" in Capture. As a test to make sure the cables are correct and are working, connect the game console directly to the HD TV set with the same video game component cables. If you see your game on the HD TV set, then the cables are o.
Step 2: Check your video cables. Try removing each cable and make sure it is firmly reseated into each device you are using. If the yellow light is not on, then either you have the wrong Video input source set or your game console is not turned on. Then you can release the power button and the PS3 video format will be set to the default p plus AV out.
Step 3: Once you have confirmed your video source is on, the Video input is correctly set and the yellow light is on the front of HD PVR 2, if you still see a black video screen in Arcsoft ShowBiz try capturing some video in the Capture module. If you can successfully playback a recording but you cannot see live video in the Preview window, there might be a video rendering problem video card drivers, hardware acceleration… Check device settings for video decoder details.
No audio in your recordings? Troubleshooting tips with the Xbox Freeze in Hauppauge Capture: on the Xbox , in 'Display settings' there's a setting called 'Display Discovery'. If you have it enabled, the Xbox automatically retrieves your TV's audio and video settings. Doing this gives you the option to choose from several resolutions to be displayed, i. So only use p or p. Freeze in Hauppauge Capture: in some PC systems, the audio Windows driver is an older version and needs to be upgraded to work with the Hauppauge Capture.
Please go to your PC's manufacturers website and find an update to your sound system. Your PS3 should now be set to Component video out and you should see video in the preview window in the Capture preview window. Plug the other end of the same cable into your TV set. This should open the Capture window. If all goes well, you should see your PS3 video in the Capture preview window. If, however, you do not see video in the Capture window, you may have to go into your PS3's Display settings and change to Component video.
To do this, push the Power button on the front of your PS3. It will turn red. The second beep means the video mode has been reset. You should now see video on your PC screen and on your TV set. Open ShowBiz and verify the correct Video input is selected. Video and audio input must be set initially for passthrough to work if you power cycle the HD PVR 2, it may revert to its default setting and will need to be set again.
Try changing the output resolution from your game console to p. If this is the case use the Component video input. You might need to reset your game console video in order for passthrough to work. To reset the video, do the following: PS3: Turn the PS3 off via the power button on the front of the unit. Flip the power switch on the back of the PS3 to the off position. Push and hold the power button on the front of the PS3 while you flip the power switch on the back of the PS3 to the on position.
Once you hear the second beep, release the power button on the front of the PS3. Your PS3 video will be reset.
Xbox: Remove any games from the optical drive. Turn the Xbox off. Turn the Xbox back on via the controller. As the console starts, press and hold the Y button, and then pull the right trigger at the same time.
Your Xbox video will be reset. Black screen in Showbiz Capture Next, check input make sure the video source setting is correct for your cabling. Do you see a valid resolution and bit rate for source? Try changing the resolution of the source.. Try to capture. If capture is successful the problem could be a video rendering problem video card drivers, hardware acceleration… If capture fails, there is something wrong with the video or audio input. Black screen with game consoles Most problems here are basic cabling and settings in game consoles.
These need to be purchased separately. Pass through problems Pass through problems, such as a black screen on your TV set even though you can record videos , are usually basic cabling and settings in Showbiz. The best way to proceed is: disconnect the game console from whatever it is connected to ….
0コメント